常州[切换城市]
注册 登录
常州桥梁切割拆除绳锯
发布时间:2018-03-08 14:36:53 修改 | 删除 | 顶一下
  • http://himg.china.cn/1/4_874_239196_500_375.jpg
地区:常州
性质:企业
关键词:电动绳锯机 液压绳锯机 绳锯切割机
发布时间:2018-03-08 14:36:53
分享到

附注:

厂家直销:液压绳锯机,电动绳锯机,金刚石锯绳,绳锯机导向轮 配件,专业针对桥梁桥墩拆除,墙体支撑梁切割,水下切割,铁路支撑梁切割机,高速公路路面切割机,建筑墙体大量切割工程,咨询热线:136 8371 7392(同步微信)
绳锯机是我公司在结合多年施工,产品造型设计经验的基础上自行研制的新一代全自动钢筋混凝土切割设备。该机器动力强劲,采用特殊定制的非标电动机为动力来源,保障切割的效率和经济性。操作柔性比较大,难度很低,施工时保证切口平直,整齐,无需修边处理,并且可以在钢筋混凝土,陶瓷,玻璃,钢板切割,工作时无振动,低噪音,定位准,无粉尘,效率高,可以切复杂截面;广泛用于加固改造,房屋,楼板,梁,柱等切割拆除行业。
由于液压钻石线锯(液压金刚石绳锯)的出现,保障了建筑保护性拆除、改造施工中,保留建筑部分的安全,广泛应用于拆迁公司、拆除公司的的施工项目中。液压绳锯是应用于建筑工程改造和加固施工的高级工程工具,作为一种特种切割工具,适用于钢筋混凝土、岩石、陶瓷、砖墙等坚硬材料的切割,广泛应用于墙体上开门、开窗、开通风口及钢筋混凝土梁、柱的切断、楼板桥梁切割及石材加工等。利用它可以使对密排钢筋混凝土和石料的技术拆除更容易,更安全,更有效。
压绳锯具有以下显著特点:降低了劳动强度,操作安全可靠,具有过载保护功能,动力强劲,提高了切割能力和劳动生产率。是拆迁拆、拆除施工项目使用的先进设备。因为它的线性切割可以使施工截面更加整齐;也因为它能够成倍提高工作速度来缩短施工工期、进一步降低劳动力成本、提高竞标优势、扩大所能接受施工工程的规模;液压系统自身的安全、可靠和稳定性,大大降低了施工设备的损耗成本;另外,类似墙锯切割这种静力切割已逐步成为一种施工和设计理念,因为它可以最大程度上保存已有结构的稳定性和安全性,广泛应用于加固公司的改造施工中的主导先进切割施工设备,替代了强击凿破或钻机排孔来施工的传统方式。
绳子驱动方式 液压
马达类型 HM-40/80(单/双缸)
最小输入功率 25/33HP
主轴输出转速 350/940/1300r/min
最大绳长 18 米
进给方式 全自动液压
切割机单元重量 64KG
主机驱动马达重量 14KG
总重量 78KG
液压动力站参数:
额定输出功率: 22/25KW
工作电压 380V50HZ
液压泵站类型 齿轮泵
主驱动马达工作流量 40-100L/min
工作压力 15-20Mpa
油箱容积 17L
重量 98kg
尺寸:650*550*1150mm
绳锯的用途及特点,为液压驱动动力装置切割设备,可对较厚实的混凝土实现各种切割。是地下室、烟囱和支柱等的切割拆除以及修缮工作适用的切割施工设备。绳锯(线锯)对密排钢筋混凝土构筑物、厚砖墙,甚至水下切割作业都能胜任。线锯(绳锯)可满足液压墙锯不及的切割深度。切割作业深度不受限制,作业环境适应性更强、作业效率更高。是液压墙锯机的后援设备。
无线遥控款:国内最成熟的工业遥控操作设备,遥控距离可达80米以上,遥控器与机器一对一配比,绝不会出现遥控器误操作别的机器,配合护罩压轮,有效减少金刚石串绳跳动,以及断绳时对人员造成人身伤害,安全系数高。高中低档,配置齐全,专业的电机智能保护系统。可定制,一个人一台机器轻松作业,切割效率是国产油压锯的1.5--2倍,降低人工,降低成本,给你创造利益最大化。正规厂家证件齐全,每台机器都有机械安全检测报告。如不会操作机器,本公司有专业师傅上门指导。工厂全新产品 质量过关已升级为不锈钢护罩。
性能参数
技术参数单位说明
绳子驱动方式--- 电动
绳子收紧方式--- 电动
绳子驱动最大功率:16.5-22KW
绳子收紧最大功率:0.2*60KW
主轴输出转速: 975R/MIN
绳子最大线速度:25.5m/s
主动轮最大尺寸:500mm
工作电压:380V
电压频率: 50HZ
接线要求: 10 平方三相五线
总重量: 248KG
外形尺寸MM 800*800*2100
1:2个驱动轮 、5个从动轮(不同品牌可能不一样)、液压马达、收绳气缸、伸缩锯架等。其中从动轮的底部有2个可以360度旋转的导向轮,此项设计在水下切割时导向绳子发挥着重大的作用。 2:产品组成:液压动力站构成:电机、油泵、油箱、过滤器、液压胶管、水冷器、高压阀等。
各部件说明
  1.主机,切割主要部件,主电机提供金刚石链条切割时所需的转动动力,小电机提供切割收紧金刚石链条所需的动力,大盘,带动金刚石链条转动。
  2双万向轮(选 配),改变切割方向时所用。
  3控制箱,控制大电机,小电机,总电源控制,其它信息显示。
  4 金钢石切割链(选配)建议选用本公司提供的专用配套金钢石切割链,以取得最大经济性。
,操作说明
1,总电源使用三相五芯,十平方,软芯电缆线,零线一定要接上,否则变频器无法启动。电线不宜过长,会降低额定电压,造成机器启动,切割功率不够。
2,大电机出线使用三相四芯,十平方,软芯电缆线。
3,小电机出线使用三相三芯,2.5 平方,软芯电缆线。
4,所有接头一定要插到底把锁扣锁紧,要不然插头间隙打火,会影响插头插座的使用寿命。
5,使用步骤:切割面的绳子出绳对准机器大电机进绳,使用万向轮的把万向轮出绳对准大电机进绳,以免不在同一轴线出现掉绳现象,起锯时绳子不宜太紧,先推上大开关把大电机启动,再设置变频器数值(建议数值4.0-7.0,具体情况参照现场情况再行调节),再调整小电机转向开关。
6,开机前确认三相电源指示灯全部亮,若有任一只灯不亮请不要开机,确认是否缺项。
7,切割完成后把大电机反向移到机器前面,直接把机器向后移动到合适位置,可直接切割。
四,安全说明
现场人员不可以在电机转动方向轴线上,以防出现断绳时发生伤人事件。操作人员在机器侧面5米以外操作机器。
本产品在使用过程中,闭杂人不要靠近施工场所,施工方需按绳子的长短画出危险区,   派出专人观望,负责现场安全。机器操作人员应在绳子旋转方向的侧面,严禁任何人员在绳子旋转线观望,以防出现意外。如因现场安全管理不到位,导致产生安全事故,本公司不负任何连带责任,特此声明。
绳锯机锯绳介绍:
本品可配套各种类型和功率的绳锯机使用,包括液压绳锯机、电动绳锯机、高频绳锯机等。
本品可应用于切割各类混凝土、钢筋混凝土材料,也可切割一般钢构件或其它金属构件。
The use and characteristic of the rope saw are the cutting equipment of the hydraulic drive power device, which can cut the thicker concrete. It is the cutting and dismantling of the basement, the chimney and the prop, as well as the suitable cutting construction equipment for the repair work. The rope saw (Xian Ju) is competent for dense reinforced concrete structures, thick brick walls, and even underwater cutting operations. (wire rope saw) can satisfy the hydraulic wall saw cutting depth less than. The cutting depth is not limited, and the working environment is more adaptable and more adaptable.
The use and characteristics of the rope saw, for the hydraulic drive power device cutting equipment, can be more thick concrete to achieve various kinds of cutting. It is the cutting and dismantling of the basement, the chimney and the prop, as well as the suitable cutting construction equipment for the repair work. The rope saw (Xian Ju) is competent for dense reinforced concrete structures, thick brick walls, and even underwater cutting operations. (wire rope saw) can satisfy the hydraulic wall saw cutting depth less than. The cutting depth is not limited, the working environment is more adaptable and the operation efficiency is higher. It is the backup equipment of the hydraulic wall saw machine.
Because the hydraulic diamond wire saw (hydraulic diamond wire saw) the emergence of building security protective demolition, renovation construction, keep the building part of the safe, widely used in Demolition Company, demolition company's construction project in. Hydraulic rope saw advanced engineering tools used in building renovation and construction, as a kind of special cutting tool, suitable for cutting of reinforced concrete, rock, ceramic, brick and other hard materials, widely used in wall door, window, air vent and reinforced concrete beam and column slab cutting, bridge cutting and stone processing. It can make it easier to dismantle reinforced concrete and stone material, safer and more effective.
The hydraulic wire saw has the following notable characteristics: reduced labor intensity, safe and reliable operation, overload protection function, strong power, improved cutting ability and labor productivity. It is the advanced equipment for demolition and dismantling and dismantling the construction projects. Because of its linear cutting can make the construction section more orderly; also because it can improve the speed of work to shorten the construction period, reduce labor cost, improve bidding advantages, expand the acceptable engineering construction scale; hydraulic system's safety, reliability and stability, greatly reduces the loss cost of construction equipment; in addition this wall, similar to saw static cutting has gradually become a construction and design concept, because it can preserve the stability and safety of the existing structure to the largest extent, leading the construction of the advanced construction equipment widely used in cutting reinforcement, instead of the attack or drill holes to break through the traditional mode of construction!
Application scope: bridge cutting, beam cutting, underwater cutting, etc.
The composition of the rope saw: the rope saw drive, the flywheel, the guide wheel, the rope saw chain (made of diamond materials).
The electric rope saw is a new generation of automatic reinforced concrete cutting equipment on the basis of our own experience in the combination of years of construction and product design. The power of the machine is strong and the special custom non - standard motor is used as the power source to ensure the efficiency and economy of cutting. Flexible operation is relatively large, the difficulty is very low, construction to ensure the cut straight, neat, without trimming, and in reinforced concrete, ceramic, glass, steel plate cutting work, no vibration, low noise, accurate positioning, no dust, high efficiency, can be widely used in cutting complex section; reinforcement of housing floor, beam, column, demolition industry.
(1) after careful design and manufacture of our technology, it is suitable for the mining of various granite and marble mines. (2) the left and right adjustment and rotation of the head are controlled by electric power, and the degree of automation is high. (3) using the imported vector frequency converter, the output torque is constant. The constant tension control principle can automatically adjust the feed speed according to the change of cutting force. The adjustment process is very stable and reliable, ensuring the best cutting state. (4) the operating table shows the parameters of the main motor current and the speed of the main flywheel in real time, and the operation is easy to adjust. (5) it has automatic and manual functions. It can be completely unmanned in the automatic operation of the equipment, and one person can operate a number of equipment. Technical parameters of unit description rope driving manner of electric rope tightening - rope electric drive power KW 22 KW 0.2*100 output power rope tightening spindle speed R/MIN line speed 975 M / s 25.5 rope wheel size MM 500 V 380 HZ 50 frequency voltage voltage wiring requirements -- 10 square three-phase five wire KG weight of 338 dimensions MM 900*900*2100 parts 1. host, cutting the main components, the main motor provides rotating power required for diamond chain cutting, cutting power, small motor provides the required tightening of diamond chain market, driven by diamond chain rotation. 2 double Cardan wheel (selected) to change the cutting direction. 3 control box, control large motor, small motor, total power control, other information display. 4 diamond cutting chain (optional) is recommended for supporting the company's diamond cutting chain of the product in use, close the miscellaneous people not to come near the construction site, the construction side according to the length of the rope drawn out of the danger zone, dispatched personnel to see, responsible for site safety. The machine operator should be in the side of the ropes in the direction of rotation, and strictly prohibit any personnel on the rope rotation line to guard against accidents. If the safety management is not in place, the company does not bear any joint liability, and hereby declares that.
Henan industrial machinery, specialized
二、 产品使用方法
1、 检查:打开包装箱,检查箱内物品是否与“装箱清单”符合;检查《产品合格证》上的“型号”是否与你所需要的型号对应(切割不同材质或不同类型设备所用绳锯型号可能不相同);
2、 剪绳:根据切割材质规格选定绳子长度,测量好长度后用剪线钳剪断;
3、 拔胶:如图示:用钳子各拔出绳子两端头的至第一粒串珠处的橡胶(有弹簧的一并拔出),并预留适当长度,不能露出基体;
4、 扭圈:将绳子绕过设备飞轮及被切割对象,手拉绳子,磨平混凝土锐角,形成所需锯路后,选择一自由端进行扭圈,不同切割材质对绳子扭圈次数要求不同,为避免产生偏磨,一般要求初始扭圈次数尽量在3~4圈/米或以上,随着绳子消耗不断增加,理论上扭圈次数应不断增加;
5、 对接:将扭圈完成后的绳子两端头塞入接头内,用液压钳压实。注意:①液压钳压实接头时,压实部位应当离接头两端口有一定距离,否则钢丝在接头处因不能自由弯曲容易产生断裂;②接头两端应与串珠端头接触,否则接头处串珠因一端失去固定力而容易产生松动。
6、 本品备有大、小两种接头,绳子使用初始阶段可用大接头,消耗过半后可换用小接头。
7、 完成上述步骤后,即可开始使用本产品。
金刚石串珠绳:50米1卷重约20KG,自带接头110个左右(单买接头1元1个,量大8毛1个)。
三、 使用注意事项

本品属于高速运转下的工具类产品,使用时如不规范操作,存在一定安全风险。主要注意事项包括以下几个方面:

1、 安全防护:本产品在高速运转状态下使用时,操作人员不允许站立在锯路所在方向及附近。

2、 冷却:本产品使用时需要确保锯路中绳子处于冷却状态,否则橡胶会过热,影响对串珠的固定效果。

3、 储存:产品不使用时,应将其存放在阴凉干燥处,避免重压或处于拉紧状态。

4、 串珠松动:①切割时,绳子局部弯曲半径过小,弯曲应力过大,导致串珠与橡胶脱开,失去橡胶对串珠的固定能力,易产生串珠松动;②冷却水不到位或冷却效果不充足,橡胶过热老化,失去对串珠固定能力,易产生串珠松动;③绳子出现卡绳,应避免强拉强扭,否则串珠易被拉脱而产生松动。
The use and characteristic of the rope saw are the cutting equipment of the hydraulic drive power device, which can cut the thicker concrete. It is the cutting and dismantling of the basement, the chimney and the prop, as well as the suitable cutting construction equipment for the repair work. The rope saw (Xian Ju) is competent for dense reinforced concrete structures, thick brick walls, and even underwater cutting operations. (wire rope saw) can satisfy the hydraulic wall saw cutting depth less than. The cutting depth is not limited, and the working environment is more adaptable and more adaptable.
The use and characteristics of the rope saw, for the hydraulic drive power device cutting equipment, can be more thick concrete to achieve various kinds of cutting. It is the cutting and dismantling of the basement, the chimney and the prop, as well as the suitable cutting construction equipment for the repair work. The rope saw (Xian Ju) is competent for dense reinforced concrete structures, thick brick walls, and even underwater cutting operations. (wire rope saw) can satisfy the hydraulic wall saw cutting depth less than. The cutting depth is not limited, the working environment is more adaptable and the operation efficiency is higher. It is the backup equipment of the hydraulic wall saw machine.
Because the hydraulic diamond wire saw (hydraulic diamond wire saw) the emergence of building security protective demolition, renovation construction, keep the building part of the safe, widely used in Demolition Company, demolition company's construction project in. Hydraulic rope saw advanced engineering tools used in building renovation and construction, as a kind of special cutting tool, suitable for cutting of reinforced concrete, rock, ceramic, brick and other hard materials, widely used in wall door, window, air vent and reinforced concrete beam and column slab cutting, bridge cutting and stone processing. It can make it easier to dismantle reinforced concrete and stone material, safer and more effective.
The hydraulic wire saw has the following notable characteristics: reduced labor intensity, safe and reliable operation, overload protection function, strong power, improved cutting ability and labor productivity. It is the advanced equipment for demolition and dismantling and dismantling the construction projects. Because of its linear cutting can make the construction section more orderly; also because it can improve the speed of work to shorten the construction period, reduce labor cost, improve bidding advantages, expand the acceptable engineering construction scale; hydraulic system's safety, reliability and stability, greatly reduces the loss cost of construction equipment; in addition this wall, similar to saw static cutting has gradually become a construction and design concept, because it can preserve the stability and safety of the existing structure to the largest extent, leading the construction of the advanced construction equipment widely used in cutting reinforcement, instead of the attack or drill holes to break through the traditional mode of construction!
Application scope: bridge cutting, beam cutting, underwater cutting, etc.
The composition of the rope saw: the rope saw drive, the flywheel, the guide wheel, the rope saw chain (made of diamond materials).
The electric rope saw is a new generation of automatic reinforced concrete cutting equipment on the basis of our own experience in the combination of years of construction and product design. The power of the machine is strong and the special custom non - standard motor is used as the power source to ensure the efficiency and economy of cutting. Flexible operation is relatively large, the difficulty is very low, construction to ensure the cut straight, neat, without trimming, and in reinforced concrete, ceramic, glass, steel plate cutting work, no vibration, low noise, accurate positioning, no dust, high efficiency, can be widely used in cutting complex section; reinforcement of housing floor, beam, column, demolition industry.
(1) after careful design and manufacture of our technology, it is suitable for the mining of various granite and marble mines. (2) the left and right adjustment and rotation of the head are controlled by electric power, and the degree of automation is high. (3) using the imported vector frequency converter, the output torque is constant. The constant tension control principle can automatically adjust the feed speed according to the change of cutting force. The adjustment process is very stable and reliable, ensuring the best cutting state. (4) the operating table shows the parameters of the main motor current and the speed of the main flywheel in real time, and the operation is easy to adjust. (5) it has automatic and manual functions. It can be completely unmanned in the automatic operation of the equipment, and one person can operate a number of equipment. Technical parameters of unit description rope driving manner of electric rope tightening - rope electric drive power KW 22 KW 0.2*100 output power rope tightening spindle speed R/MIN line speed 975 M / s 25.5 rope wheel size MM 500 V 380 HZ 50 frequency voltage voltage wiring requirements -- 10 square three-phase five wire KG weight of 338 dimensions MM 900*900*2100 parts 1. host, cutting the main components, the main motor provides rotating power required for diamond chain cutting, cutting power, small motor provides the required tightening of diamond chain market, driven by diamond chain rotation. 2 double Cardan wheel (selected) to change the cutting direction. 3 control box, control large motor, small motor, total power control, other information display. 4 diamond cutting chain (optional) is recommended for supporting the company's diamond cutting chain of the product in use, close the miscellaneous people not to come near the construction site, the construction side according to the length of the rope drawn out of the danger zone, dispatched personnel to see, responsible for site safety. The machine operator should be in the side of the ropes in the direction of rotation, and strictly prohibit any personnel on the rope rotation line to guard against accidents. If the safety management is not in place, the company does not bear any joint liability, and hereby declares that.
Henan industrial machinery, specializedhttp://himg.china.cn/1/4_355_238234_500_375.jpghttp://himg.china.cn/1/4_913_237584_500_751.jpg
5、 断绳:①钢丝从接头断:往往是接头与钢丝没有压实紧密,或接头压实方法不对,导致钢丝从接头处脱开或断裂;②非接头处断绳:往往是由于串珠松动后,在高速旋转下很快磨断钢丝表层,降低钢丝强度而产生断绳,应在发现串珠松动后,在松动处剪断两颗串珠后重接,或砸紧松动的串珠让其不产生旋转,可避免钢丝断开。

6、 橡胶脱开与开裂:①上述“串珠松动”中所提各种情况,均易导致橡胶开裂;②检查导轮橡胶磨损状态,避免绳子在橡胶轮上打滑,因无冷却防护导致绳子过热,易出现橡胶脱开现象。

7、 偏磨:①扭圈次数不够,导致绳子扭转力远小于切割应力,绳子难以圆周偏转,易产生偏磨;②切割时绳子进给过快,切割应力远大于正常扭转力,绳子易产生偏磨。
厂家直销:液压绳锯机,电动绳锯机,金刚石锯绳,绳锯机导向轮 配件,专业针对桥梁桥墩拆除,墙体支撑梁切割,水下切割,铁路支撑梁切割机,高速公路路面切割机,建筑墙体大量切割工程,咨询热线:136 8371 7392(同步微信)

发布人信息
用户:hnygjx01
注册:18-03-06 10:01
离线:18-05-30 16:47
级别:钻石会员
用户认证:企业会员身份还未认证邮箱认证会员手机还未认证
联系人:叶经理
电话号码:13683717392
手机号码:13683717392 河南郑州移动 查询更多
QQ 号码:1742461343
MSN 帐号:-
邮箱帐号:1742461343@qq.com
信息发布2